Fit & cutting
Check the board width, cut interval, connection space and lengths against the fixture drawing. Keep solder joints away from the tightest clearances.
SMD · BEXLIGHT
2835 High Efficiency LED Strip
Model SR005-160P2835IP20-ER80
An SMD LED strip for task, accent and display lighting. Choose the white-light or colour configuration and check its fit in your selected profile.
- Supply voltage
- 24V
- Dimensions
- 8*5000mm
- Cut interval
- 50mm
- Protection
- IP20
- Colour temperature options
- 2700, 3000, 4000, 6500
- CRI options
- 80Ra
For fixture development, project supply and repeat B2B orders. Include the quantity and intended configuration in your enquiry.
Build the specification around the assembly.
SMD LED strips serve task, accent and display lighting where the PCB dimensions, LED spacing and optical assembly can be matched to the fixture. Select against the complete detail rather than comparing a single catalogue figure.
Plan the complete lighting assembly.
Coordinate this model with the selected profile, diffuser, driver, sensors and quick-connect harness. Discuss Pre-Cut Custom Lengths and Custom Assembly & Kitting against the drawings; a catalogue strip alone is not a ready-to-install kit.
MODEL DATA
The details
that define the model.
Match the selected configuration to your order and fixture drawing. Options and catalogue ranges describe available configurations rather than simultaneous ratings.
Model reference
SR005-160P2835IP20-ER80
| Parameter | Value / options |
|---|---|
| Luminous output | To confirm |
| Efficacy | 150 lm/W |
| Power per metre | 14.4 W/m |
| LEDs per metre | 160 |
| Supply voltage | 24V |
| Dimensions | 8*5000mm |
| Cut interval | 50mm |
| Minimum bend diameter | >60mm |
| Copper foil | 3OZ |
| Protection | IP20 |
| Colour temperature options | 2700, 3000, 4000, 6500 |
| CRI options | 80Ra |
| LED type | 2835 |
Full catalogue record
Retained for reference; confirm options for the supplied configuration.
| Power(W/m) | 9.7-14.4 |
|---|---|
| Voltage | 24V |
| Lumen output | 150LM/W |
| CCT | 2700, 3000, 4000, 6500 |
| CRI | 80Ra |
| LED Type | 2835 |
| LEDs/m | 160LEDs/m |
| Dimension | 8*5000mm |
| Cut unit | 50mm |
| Bend Diameter | >60mm |
| Copper Foil | 3OZ |
| IP Rating | IP20 |
| Warranty | 3-5 years |
Check the fit.
Approve the result.
Use the model information alongside your fixture and installation requirements. The sample should answer the questions that a catalogue image cannot.
Light effect
Review the LED spacing, diffuser depth and viewing angle. Approve a sample in the actual channel and finish when individual LED images would affect the result.
Order definition
Keep the model reference, selected colour, section lengths, wire exits and quantities in the purchase specification. Resolve any source-data differences before approval.
Plan this source
in the right detail.
This white-light SMD source can be compared for task and display assemblies. Review source spacing, selected colour and diffuser depth; no application performance is implied by the catalogue image. These are application planning routes, subject to configuration and sample review.
Under-Cabinet Task Lighting
Set the light line around the worktop and backsplash. Check the channel angle, diffuser, hand position and feed location on the cabinet drawing.
View the solution →
Under-Shelf Recessed Joinery Lighting
Coordinate machining, light direction and the shelf support before the section is released for cutting.
View the solution →
Luxury Jewelry & Watch Display
Use a representative display mock-up to agree sparkle, metal tone, reflections and visitor comfort.
View the solution →TECHNICAL SUPPORT
Put the right information
behind the order.
Need a model datasheet, dimensional drawing or wiring information? Send the model reference and the configuration you are considering so the appropriate documents can be identified.
For a quotation, include the application, quantity and unit, section lengths, colour requirement, target market and any fixture drawings.
Request documents or discuss this modelFREQUENTLY ASKED QUESTIONS
Questions about SR005-160P2835IP20-ER80
Model selection, installation scope and the information needed for a B2B quotation.
Ask a project question →What supply voltage does SR005-160P2835IP20-ER80 need?
The model record lists 24V. Match the selected configuration to the driver output and confirm the complete branch load, wiring and control arrangement. Do not connect a low-voltage strip directly to mains power.
Can this model be cut to our furniture dimensions?
The listed cut interval is 50mm. Work to the permitted cut marks and allow space for the termination, cable exit and mounting detail. Finished assemblies need a length schedule; the cut interval does not mean every requested dimension can be supplied exactly.
Where does the listed IP20 protection apply?
This is the protection value shown for the catalogue source configuration. Check the intended exposure, cut ends, connections and mounting assembly separately. A reel rating does not automatically apply to a cut and reassembled lighting system.
How can we check whether individual LEDs will be visible?
Review the source spacing together with the profile depth, diffuser and viewing distance. A strip photograph cannot establish the appearance through your chosen cover. Use a representative installed section when visible LED images would affect the furniture finish.
Is this catalogue item a complete plug-and-play kit?
This page identifies the light source. A complete assembly also defines the profile, diffuser, driver, controls and harness. Send the fixture drawing and quantities to scope pre-cut lengths, prewired connections and packing by module.
What should we include when requesting this model for a project?
Quote SR005-160P2835IP20-ER80 and specify the selected colour, finished lengths, feed exits, quantity and unit. Add the application drawings, target market and required documents. Catalogue options and ranges need to be resolved into one identifiable order configuration.
Compare within
the range.
Check the individual configuration and physical dimensions before substituting a model.
